Silver Threads

a knitting blog with occasional side trips

Supposedly simple double orbital

4 Comments

Having made the two Byzantine bracelets and enjoyed doing so (eventually),  I wanted to learn a different weave. I had a lot of jump rings left over from the first Byzantine bracelet, so I tried making samples of different weaves. Mixed success on this front. Some, like the spiral weave, worked fine, although I discovered soon enough that spiral didn’t interest me all that much. But much of the time, even though I understood how the rings were supposed to go together, I couldn’t physically get them to do what I wanted. Welcome to the concept of “aspect ratio.” Basically, jump rings vary in their inner diameter and the thickness of the wire they’re made from, and the two together are the aspect ratio (aspect ratio = inner diameter divided by wire diameter…okay, I’ll stop with the math now). If the wire is too thick in proportion to the inner diameter for the weave you’re attempting, you’re not going to be able to cram the rings into the space available. If the wire is too thin, I’d guess you’d be able to make the weave, but it’d be flimsy and loose and not look very attractive. This latter possibility is all hypothetical to me, since I was having the first problem. Apparently 16 g rings of 7/32″ inner diameter are fine for the Byzantine and spiral weaves, but other weaves like double spiral and box were just not working.

I put the loose rings aside and bought another kit, figuring that at least they’d give me rings that were the right size for the design. Sure, I’d decided these kits weren’t great for beginners, but now I had all the experience of two bracelets behind me (!). Plus, I liked several of the vendor’s other designs. I chose one in double orbital weave and in an attractive combination of rainbow  and silver rings. Silver colored, that is, not real silver. I was still going to be working with enameled copper.

The first stage was encouraging as all get out: make a chain of the silver rings. This took me twenty minutes, tops. Two rings alternating with one ring. I gloated silently at my proficiency. Yes, all problems were behind me and I was on my way to being a chain maille queen. All I needed to do was add in the colored rings, and…

…nope.

It sounded simple. Lay the chain on the mat, which would cause the paired rings to move apart slightly, like a metal Venn diagram. Then take a colored ring and wrap it around the marquis shape in the center of the “diagram,” close it, then repeat with a second ring of the same color. Again, does this not sound simple?

The first ring of each pair, which I thought would be the more challenging of the two, went in with a bit of a fuss, but not much. The second was hell. I’d poke one end in, and you’d think that the first ring would hold the whole arrangement steady, but no. The second ring would get snagged in the first ring, or it’d go through the silver rings wrong, or it’d go through one of the single silver rings. Twenty minutes for the entire silver chain turned into fifteen to twenty minutes for each second colored ring, and often that ring was scratched by the time I finally got it closed.

The solution was in how to insert them. The best way I can describe it was that at first, I was putting the rings in like a needle and thread: point one end in the direction I wanted it to go and use the pliers to pull the ring into position, assuming that the rest of the ring would follow. That’s what the various books I’d read had instructed me to do, and it had worked just fine for Byzantine weave. For double orbital, I needed to put the ring in like a staple: both ends in at once and then close the ring. Okay, jump rings aren’t staples, and I couldn’t put them in simultaneously. But the moment I got one end in, I’d move to put the other end in, and then wiggle the ring a bit to bring both ends up where I could grab them again and close the ring. Success, usually in two minutes!

And finally: one rainbow double orbital bracelet:

Chain maille bracelet, double orbital weave

I’m taking a break from these kits. I’d still like to make some of these designs, but clearly my tolerance level for working with small enameled copper rings is not high. Plus, I’ve ordered several packs of aluminum rings in an aspect ratio that should work better for the weaves that interest me. And after I’ve played with them a while, maybe niobium? I have ideas for how to use that in a bracelet. It’s too bad I don’t wear bracelets in cold weather because they’re hidden by long sleeves, since at this rate, I’m going to have bracelets all over the place.

Advertisements

4 thoughts on “Supposedly simple double orbital

  1. Wonderful, wonderful, wonderful!

    Like

  2. I think the colors are really cute! I would want to do a series of these and hang them outside as a rain chain! 🙂

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s